# EMI and RFI Shielding Cases: When Plastic Is Not Enough

> When sensitive electronics need electromagnetic shielding from a transport case: aluminum construction, conductive coatings and shielded gaskets, with attenuation expectations.

Human-readable page: https://kexinn.org/emi-rfi-shielding-cases/
Site overview for AI agents: https://kexinn.org/llms.txt

## Page content

DOC **KB-EMI-018**REV 2026-09-21CLASS: PUBLIC

## EMI and RFI Shielding Cases: When Plastic Is Not Enough

Direct answer

A standard plastic protective case provides no meaningful EMI/RFI shielding. When electronics must be shielded in transit or in use, the three established paths are: aluminum case construction (excellent inherent conductivity), plastic shells with conductive coatings (vacuum-metallized or conductive-paint interiors), and EMI gasketing — conductive elastomer seals that close the lid gap electrically. Shielding performance is set by the weakest path: an unsealed plastic lid gap defeats an aluminum body.

## §01The three approaches

| Approach | Typical attenuation | Strengths | Watch out for |
|---|---|---|---|
| Aluminum case | very high, broadband | also fire/heat tolerant; durable threads | weight, denting, cost |
| Metallized / conductive-coated plastic | moderate, frequency-dependent | keeps weight and corrosion resistance of plastic | coating wear at latch/hinge points |
| EMI gaskets on any shell | — (completes the enclosure) | closes seams and lid lines | must be inspected; takes compression set like any elastomer |

## §02Engineering notes

- **Apertures dominate:** a cable pass-through or valve hole acts as an antenna slot. Every penetration needs a filtered connector or a waveguide-below-cutoff design.
- **Galvanic compatibility:** pair conductive gaskets with the shell metal plating to avoid corrosion couples (aluminum body needs stainless or aluminized gasket fillers).
- **Testing:** shielding effectiveness is measured per IEEE 299 on the assembled enclosure — ask for the test frequency range, not just "shielded".
- **Combine with ESD foam:** shielding the enclosure and using dissipative foam inside are complementary, not redundant.

**Reality check:** many buyers specify "EMI case" when they actually need ESD-safe packaging. Shielding blocks external RF in/out; ESD protection prevents static discharge to components. If the threat is a charged operator touching a PCB, anti-static foam and packaging discipline solve it at a fraction of the cost.

## Frequently asked questions

### Do waterproof plastic cases provide EMI shielding?

No. Unfilled plastics like PP and ABS are transparent to RF. Shielding requires a conductive enclosure — aluminum, metallized plastic, or conductive gaskets closing the seams of a coated shell.

### What is an EMI gasket?

A conductive elastomer seal — silicone or EPDM loaded with silver, nickel-graphite or silver-aluminum particles — that both seals the lid mechanically and closes the enclosure electrically across the seam.

### Is an aluminum case always better for electronics?

Aluminum offers real shielding plus heat tolerance, at the cost of weight and price. For shielded-but-portable needs, a metallized plastic case with EMI gasketing is often the better weight/cost compromise.

### How is shielding effectiveness specified?

As attenuation in dB across a stated frequency range, measured on the assembled enclosure (per standards such as IEEE 299). A quote that omits the frequency range is not a shielding specification.

## Related guides

[KB-LOG-017Export Packing for Protective Cases: Master Cartons, Pallets and Container Loading](https://kexinn.org/export-packing-and-container-loading/)[KB-MST-019Moisture and Corrosion Control Inside Protective Cases](https://kexinn.org/moisture-and-corrosion-control-in-cases/)[KB-IND-020Which Case for Which Job: Selection by Industry and Use](https://kexinn.org/case-selection-by-industry/)

REF KB-EMI-018 · Published 2026-09-21 · Reviewed by the KeXin Materials engineering team · Sources: IEC 60529; ISO 6346; ATA 300; MIL-STD-810; Incoterms® 2020
